|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
MICROWAVE CORPORATION v00.1002 HMC364G8 SMT GaAs HBT MMIC DIVIDE-BY-2, DC - 13.0 GHz Features Ultra Low SSB Phase Noise: -145 dBc/Hz Wide Bandwidth Output Power: 7 dBm Single DC Supply: +5V 8 Lead Hermetic SMT Package Typical Applications Prescaler for DC to X Band PLL Applications: * Point-to-Point / Multi-Point Radios * VSAT Radios 10 FREQ. DIVIDER & DETECTORS - SMT * Fiber Optic * Test Equipment * Space & Military Functional Diagram General Description The HMC364G8 is a low noise Divide-by-2 Static Divider with InGaP GaAs HBT technology in an 8 lead glass/metal surface mount (hermetic) package. This device operates from DC (with a square wave input) to 13 GHz input frequency with a single +5.0V DC supply. The low additive SSB phase noise of -145 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. Electrical Specifications, TA = +25 C, 50 Ohm System, Vcc= 5V Parameter Maximum Input Frequency Minimum Input Frequency Input Power Range Sine Wave Input. {1} Fin = 1 to 9 GHz Fin = 9 to 12 GHz Fin = 12 to 13 GHz Output Power Fin = 6 GHz Fin = 9 GHz Fin = 12 GHz Fin = 13 GHz Reverse Leakage SSB Phase Noise (100 kHz offset) Output Transition Time Supply Current (Icc) Both RF Outputs Terminated Pin = 0 dBm, Fin = 6 GHz Pin = 0 dBm, Fout = 882 MHz -15 -15 -10 3 1 -2 -3 Conditions Min. 13 Typ. 13.5 0.2 >-20 >-20 >-15 7 5 2 1 40 -145 100 110 0.5 +10 +5 +2 Max. Units GHz GHz dBm dBm dBm dBm dBm dBm dBm dB dBc/Hz ps mA 1. Divider will operate down to DC for square-wave input signal. 10 - 32 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.1002 HMC364G8 SMT GaAs HBT MMIC DIVIDE-BY-2, DC - 13.0 GHz GaAs MMIC SUB-HARMONICALLY Input Sensitivity Window17 Temperature PUMPED MIXER vs. - 25 GHz Input Sensitivity Window, T= 25 C 20 20 10 10 INPUT POWER (dBm) Min Pin +25C Max Pin +25C Min Pin +85C Max Pin +85C Min Pin -40C Max Pin -40C INPUT POWER (dBm) 0 Recommended Operating Window 0 -10 -10 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 33 -20 -20 -30 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 INPUT FREQUENCY (GHz) -30 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 INPUT FREQUENCY (GHz) Output Power vs. Temperature 10 9 8 7 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 0 1 2 3 4 SSB Phase Noise Performance, Pin= 0 dBm, T= 25 C 0 -20 SSB PHASE NOISE (dBc/Hz) OUTPUT POWER (dBm) -40 -60 -80 -100 -120 -140 -160 2 10 + 25C + 85C - 40C 5 6 7 8 9 10 11 12 13 14 15 INPUT FREQUENCY (GHz) 10 3 10 4 10 5 10 6 10 7 OFFSET FREQUENCY (Hz) Output Harmonic Content, Pin= 0 dBm, T= 25 C 0 Reverse Leakage, Pin= 0 dBm, T= 25 C 0 Both Output Ports Terminated One Output Port Terminated OUTPUT LEVEL (dBm) -10 POWER LEVEL (dBm) -10 -20 -20 -30 PFEEDTHRU 3rd HARMONIC -30 -40 -40 -50 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 INPUT FREQUENCY (GHz) -50 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 INPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.1002 HMC364G8 SMT GaAs HBT MMIC DIVIDE-BY-2, DC - 13.0 GHz Output Voltage Waveform, Pin= 0 dBm, Fout= 882 MHz, T= 25 C 700 600 500 400 300 200 100 0 -100 -200 -300 -400 -500 -600 -700 22.7 22.9 23.1 23.3 23.5 23.7 23.9 24.1 24.3 24.5 24.7 TIME (nS) Absolute Maximum Ratings RF Input (Vcc = +5V) Vcc Channel Temperature (Tc) Continuous Pdiss (T = 85 C) (derate 11.9 mW/ C above 85 C) Storage Temperature Operating Temperature +13 dBm +5.5V 135 C 593 mW -65 to +150 C -40 to +85 C 10 FREQ. DIVIDER & DETECTORS - SMT AMPLITUDE (mV) Typical Supply Current vs. Vcc Vcc (V) 4.75 5.0 5.25 Icc (mA) 100 110 120 Note: Divider will operate over full voltage range shown above Outline Drawing NOTES: 1. PACKAGE MATERIAL: ALUMINA LOADED BOROSILICATE GLASS. 2. LEAD, BASE, COVER MATERIAL: KOVARTM (#7052 CORNING). 3. PLATING: ELECTROLYTIC GOLD 50 MICROINCHES MIN., OVER ELECTROLYTIC NICKEL 50 MICROINCHES MIN. 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. TOLERANCES: .005 [0.13] UNLESS OTHERWISE SPECIFIED. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 10 - 34 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.1002 HMC364G8 SMT GaAs HBT MMIC DIVIDE-BY-2, DC - 13.0 GHz Pin Description Pin Number Function Description Interface Schematic 1 IN RF Input must be DC blocked. 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 35 2, 6 N/C No connection. 3 IN RF Input 180 out of phase with pin 1 for differential operation. AC ground for single ended operation. 4 GND Ground: Backside of package has exposed metal ground which must be connected to a RF/DC ground. 5 OUT Divided output 180 out of phase with pin 7. 7 OUT Divided Output. 8 VCC Supply voltage 5V 0.25V. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v00.1002 MICROWAVE CORPORATION HMC364G8 SMT GaAs HBT MMIC DIVIDE-BY-2, DC - 13.0 GHz Evaluation PCB 10 FREQ. DIVIDER & DETECTORS - SMT List of Materials Item J1 - J3 C1 - C4 C5 C6 U1 PCB* Description PC Mount SMA RF Connector 100 pF Capacitor, 0402 Pkg. 1000 pF Capacitor, 0603 Pkg. 10 uF Tantalum Capacitor HMC364G8 Divide-by-2 104627 Eval Board * Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and backside ground slug should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. This evaluation board is designed for single ended input testing. J2 and J3 provide differential output signals. 10 - 36 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v00.1002 MICROWAVE CORPORATION HMC364G8 SMT GaAs HBT MMIC DIVIDE-BY-2, DC - 13.0 GHz Application Circuit 10 FREQ. DIVIDERS & DETECTORS - SMT For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 37 |
Price & Availability of HMC364G8 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |